All Samsung Washing Machine Error Codes

In this article, we will show how to identify error code on a Samsung washing machine and how to fix it.

When SAMSUNG washing machine got a problem, the error code will be displayed on the user interface panel, telling you what part of the washer malfunction and require your attention.

In most cases, this is indicated by two figures on the digital display at the front.

Samsung Washing Machine Error Codes nd, 5E, SE, 5C, SC, 1 5C.

The washer was unable to drain within 10 minutes.

First of all check your drain filter (at the bottom on the left side) to make sure it’s not clogged.

You might need to drain water from the drum manually first and only then open the drain filter.

If you hear kinda rattling noise coming from the pump, that’s mean drain pump coming to the end, because drain motor impeller coming off from the motor shaft and slipping off.

In this case, only one solution is to change the drain pump.

Samsung Washing Machine Error Codes LO, dS, d5, FL, LO, L0, dE, dE1, dE2, dc, dL, 1 dC, 1dC4, 1dC1

Meaning, door lock unable to lock after several attempts.

In most cases its just the malfunction of the lock.

The control board unable to confirm that the door lock physically locked.

In this case you can’t fix the lock, just replace it.

Samsung Washing Machine Error Codes nF, 4C, 4E, 1 4C –

Water not filling up the washer.

There are two common things that could happen.

One of them is faulty water inlet valve, second is water tap being OFF.

You need to remove the top cover on the washer and check water inlet valves for continuity with a multimeter.

Don’t forget to unplug the machine.

If you will get ZERO continuity that means the valve is defective.

Samsung Washing Machine Error Codes 1E, LE, 1C, LC, LC1, 1 1C, 1 LC –

Water level sensor failure or water hose connected to the sensor being detached from the drum because of vibration or water hose clogged with some gunk and sensor unable to measure how much water left in the drum.

You need to detached hose from the sensor and just blow into the hose to make sure its not clogged.

If its all ok, then you just need to replace a sensor with a new one.

In this article, we will show how to identify error code on a Samsung washing machine and how to fix it.

When SAMSUNG washing machine got a problem, the error code will be displayed on the user interface panel, telling you what part of the washer malfunction and require your attention.

In most cases, this is indicated by two figures on the digital display at the front.

Samsung Washing Machine Error Codes nd, 5E, SE, 5C, SC, 1 5C.

The washer was unable to drain within 10 minutes.

First of all check your drain filter (at the bottom on the left side) to make sure it’s not clogged.

You might need to drain water from the drum manually first and only then open the drain filter.

If you hear kinda rattling noise coming from the pump, that’s mean drain pump coming to the end, because drain motor impeller coming off from the motor shaft and slipping off.

In this case, only one solution is to change the drain pump.

Samsung Washing Machine Error Codes LO, dS, d5, FL, LO, L0, dE, dE1, dE2, dc, dL, 1 dC, 1dC4, 1dC1

Meaning, door lock unable to lock after several attempts.

In most cases its just the malfunction of the lock.

The control board unable to confirm that the door lock physically locked.

In this case you can’t fix the lock, just replace it.

Samsung Washing Machine Error Codes nF, 4C, 4E, 1 4C –

Water not filling up the washer.

There are two common things that could happen.

One of them is faulty water inlet valve, second is water tap being OFF.

You need to remove the top cover on the washer and check water inlet valves for continuity with a multimeter.

Don’t forget to unplug the machine.

If you will get ZERO continuity that means the valve is defective.

Samsung Washing Machine Error Codes 1E, LE, 1C, LC, LC1, 1 1C, 1 LC –

Water level sensor failure or water hose connected to the sensor being detached from the drum because of vibration or water hose clogged with some gunk and sensor unable to measure how much water left in the drum.

You need to detached hose from the sensor and just blow into the hose to make sure its not clogged.

If its all ok, then you just need to replace a sensor with a new one.